
Product Description:
Photovoltaic connector, Photovoltaic connector, housing material: PPE, color: black, min. conductor cross section: 4 mm², Connection method: Crimp, Type of contact: Pin, cable length: 130. can only be released using a tool

GTIN
: 04046356671446
Series
: PV-FT-CM-C-4-130-RD
Type
: Fotovoltaïsche connector
Key Features
- Photovoltaic connector
- Photovoltaic connector
- housing material: PPE
- color: black
- min. conductor cross section: 4 mm²
- Connection method: Crimp
- Type of contact: Pin
- cable length: 130. can only be released using a tool
Training Data Goes here
Dimensions
Fixed cable length
130
External cable diameter
4.6 mm ±0.15 mm
Ambient conditions
Degree of protection (when plugged in)
IP66 / IP68 (2 m / 24 h)
Degree of protection (not plugged in)
IP65
Ambient temperature (operation)
-40 °C ... 85 °C
Ambient temperature (assembly)
-25 °C ... 50 °C
General
Design
Pin
Tightening torque nut
1.8 Nm ±0.1 Nm
Insertion force
45 N ±10 N
Disconnect force
250 N ±50 N
Pull-out force of cable >= disconnect force
> 80 N
Degree of pollution
3
Degree of protection
IP65
Current
35
Rated surge voltage (III/3)
16
pluggable
Yes
Rated voltage
1500
Rated current (2.5 mm²)
----
Rated current (4.0 mm²)
35
Rated current (6.0 mm²)
----
Nominal cross section
4
Protection class
II
Material
Color
black
Insulating material
mPPE
Contact material
Cu
Contact surface material
Ag
Connection data
Connection method
Crimp
Connection capacity
4
Contact resistance with connected conductor
0.45 mΩ
Cable type
S02
Type of contact
Pin
Conductor
Outer sheath, material
PE-X
External sheath, color
red
Standards and Regulations
Halogen-free
yes
Flammability rating according to UL 94
V0
Safety note
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
Safety note
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
Safety note
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
Safety note
• The products are suitable for applications in plant, controller, and electrical device engineering.
Safety note
• Assembled products may not be manipulated or improperly opened.
Safety note
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
Safety note
• When using the product in direct connection with third-party manufacturers, the user is responsible.
Safety note
• For operating voltages > 50 V AC, conductive connector housings must be grounded
Safety note
• Ensure that the protective or functional ground has been properly connected.
Safety note
• Observe the corresponding technical data. You will find information:o On the product On the packing label In the supplied documentation Online at phoenixcontact.com/products under the product
Safety note
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
Safety note
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
Safety note
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Safety note
• Operate the connector only when it is fully plugged in and interlocked.
Safety note
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
Safety note
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
Environmental Product Compliance
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
China RoHS
No hazardous substances above threshold values
There is no certificate available for this product.