
Product Description:
Device connector for front wall, SB, angled rotatable, shielded: yes, for standard and SPEEDCON interlock, M40, type of contact: Pin, Crimp connection, Axial O-ring, 4x Ø4,2

GTIN
: 04055626194936
Series
: SB-8EPCD8AA700S
Type
: Apparaatconnector voorwand
Key Features
- Device connector for front wall
- SB
- angled rotatable
- shielded: yes
- for standard and SPEEDCON interlock
- M40
- type of contact: Pin
- Crimp connection
- Axial O-ring
- 4x Ø4
Advantages
• Easy connection, thanks to infinitely adjustable cable outlet direction up to 310°
• Transmission of signals, data, and power in just a single connector
• CAT5 data interface for up to 100 Mbps
• Mechanical coding reliably prevents incorrect connections
• Safe use in the field, thanks to high degree of protection
• Consistent EMC protection for reliable connection solutions in the industrial environment
Training Data Goes here
Temperature range
Temperature range
-40 °C ... 115 °C (see derating curve)
Standards and Regulations
Safety note
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
Safety note
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
Safety note
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
Safety note
• The products are suitable for applications in plant, controller, and electrical device engineering.
Safety note
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
Safety note
• Assembled products may not be manipulated or improperly opened.
Safety note
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
Safety note
• When using the product in direct connection with third-party manufacturers, the user is responsible.
Safety note
• For operating voltages > 50 V AC, conductive connector housings must be grounded
Safety note
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
Safety note
• Observe the corresponding technical data. You will find information:o On the product On the packing label In the supplied documentation Online at phoenixcontact.com/products under the product
Safety note
• Only use tools recommended by Phoenix Contact
Safety note
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
Safety note
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
Safety note
• Operate the connector only when it is fully plugged in and interlocked.
Safety note
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
Safety note
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
Safety note
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Data of the insulating body
Contact connection method
Crimp connection
Type of contacts
Pin
Application
Hybrid
Number of positions
13
Direction of rotation
Standard
Contact diameter of power contacts
3.6 mm
Litz wire cross section of power contacts min.
1
Litz wire cross section of power contacts max.
10
Rated current for power contacts
70
Rated voltage
630
Rated surge voltage
6
Overvoltage category
III
Degree of pollution
3
Contact diameter of signal contacts
1
Litz wire cross section of signal contacts min.
0.06 mm²
Litz wire cross section of signal contacts max.
1.5 mm²
Nominal current per signal contact
8
Rated voltage of signal contact
500
Rated surge voltage
1.5 kV
Contact diameter, data contacts
0.8 mm
Litz wire cross section, data contacts, min.
0.08 mm²
Litz wire cross section, data contacts, max.
0.5 mm²
Rated current of each data contact at 25°C
3.6 A
Rated voltage of data contact
50
Material
1.5 kV
Housing data
Housing material
Turned parts: copper zinc alloy (CuZn), die-cast parts: zinc (GD-Zn)
Type of locking
for standard and SPEEDCON interlock
Degree of protection (when plugged in)
IP68/IP69K
Thread type
M40
Environmental Product Compliance
REACh SVHC
Lead 7439-92-1
China RoHS
Environmentally Friendly Use Period = 50 years
EAC B.01687