
Product Description:
Coupler connector, straight, for standard and SPEEDCON interlock, M17, number of positions: 6+PE, type of contact: Pin, Crimp connection, shielded: yes, cable diameter range: 10 mm ... 12.5 mm

GTIN
: 04046356622936
Series
: ST-6EP1N8A9005S
Type
: Koppelconnectoren
Key Features
- Coupler connector
- straight
- for standard and SPEEDCON interlock
- M17
- number of positions: 6+PE
- type of contact: Pin
- Crimp connection
- shielded: yes
- cable diameter range: 10 mm ... 12.5 mm
Advantages
• Consistent EMC protection for reliable connection solutions in the industrial environment
• Crimping connection: vibration- and temperature-resistant assembly
• Flexible use: reliably connect various cable diameters
Training Data Goes here
General
Note
Order information: Order crimp contacts Ø 1 mm separately
Type of locking
for standard and SPEEDCON interlock
Direction of rotation of contact chamber numbering
Standard
Coding
N
Contact connection method
Crimp connection
Type of contacts
Pin
Number of positions
7
Contact diameter of power contacts
1
Rated current for power contacts
14
Contact diameter of signal contacts
1
Conductor entry
10 mm ... 12.5 mm
Pg housing screw connection
none
Ambient conditions
Ambient temperature
-40 °C ... 125 °C
Degree of protection
IP67
Specifications according to DIN EN 61984:2001
Installation height max.
3000
Nominal / operating voltage of power contacts
630
Rated surge voltage of power contacts
6
Overvoltage category of power contacts
III
Degree of pollution of power contacts
3
Standards and Regulations
Safety note
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
Safety note
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
Safety note
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
Safety note
• The products are suitable for applications in plant, controller, and electrical device engineering.
Safety note
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
Safety note
• Assembled products may not be manipulated or improperly opened.
Safety note
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
Safety note
• When using the product in direct connection with third-party manufacturers, the user is responsible.
Safety note
• For operating voltages > 50 V AC, conductive connector housings must be grounded
Safety note
• Ensure that the protective or functional ground has been properly connected.
Safety note
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
Safety note
• Only use tools recommended by Phoenix Contact
Safety note
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
Safety note
• Operate the connector only when it is fully plugged in and interlocked.
Safety note
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
Safety note
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
Safety note
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Environmental Product Compliance
REACh SVHC
Lead 7439-92-1
China RoHS
Environmentally Friendly Use Period = 50 years