{"Temperature range"=>[{"name"=>"Temperature range", "value"=>"-40 °C ... 115 °C (see derating curve)"}]}{"Standards and Regulations"=>[{"name"=>"Safety note", "value"=>"WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property."}, {"name"=>"Safety note", "value"=>"• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible."}, {"name"=>"Safety note", "value"=>"• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product."}, {"name"=>"Safety note", "value"=>"• The products are suitable for applications in plant, controller, and electrical device engineering."}, {"name"=>"Safety note", "value"=>"• When operating the connectors in outdoor applications, they must be separately protected against environmental influences."}, {"name"=>"Safety note", "value"=>"• Assembled products may not be manipulated or improperly opened."}, {"name"=>"Safety note", "value"=>"• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products)."}, {"name"=>"Safety note", "value"=>"• When using the product in direct connection with third-party manufacturers, the user is responsible."}, {"name"=>"Safety note", "value"=>"• For operating voltages > 50 V AC, conductive connector housings must be grounded"}, {"name"=>"Safety note", "value"=>"• Ensure that the protective or functional ground has been properly connected."}, {"name"=>"Safety note", "value"=>"• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector"}, {"name"=>"Safety note", "value"=>"• Only use tools recommended by Phoenix Contact"}, {"name"=>"Safety note", "value"=>"• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product."}, {"name"=>"Safety note", "value"=>"• Operate the connector only when it is fully plugged in and interlocked."}, {"name"=>"Safety note", "value"=>"• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards."}, {"name"=>"Safety note", "value"=>"• Observe the minimum bending radius of the cable. Lay the cable without twisting it."}, {"name"=>"Safety note", "value"=>"• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12)."}]}{"Data of the insulating body"=>[{"name"=>"Note", "value"=>"Order information: Crimp contacts, 4x Ø 0.8 mm, 4x Ø 1 mm, 5x Ø 2 mm, order separately"}, {"name"=>"Protection against electric shock", "value"=>"IEC 61984 and VDE 0623"}, {"name"=>"Data rate", "value"=>"100"}, {"name"=>"Coding", "value"=>"N"}, {"name"=>"Insulator material", "value"=>"PA 6.6"}, {"name"=>"Insertion/withdrawal cycles mechanical", "value"=>"100"}, {"name"=>"Contact connection method", "value"=>"Crimp connection"}, {"name"=>"Type of contacts", "value"=>"Pin"}, {"name"=>"Application", "value"=>"Hybrid"}, {"name"=>"Number of positions", "value"=>"13"}, {"name"=>"Direction of rotation", "value"=>"Standard"}, {"name"=>"Contact diameter of power contacts", "value"=>"2"}, {"name"=>"Litz wire cross section of power contacts min.", "value"=>"0.25 mm²"}, {"name"=>"Litz wire cross section of power contacts max.", "value"=>"4"}, {"name"=>"Rated current for power contacts", "value"=>"30"}, {"name"=>"Note", "value"=>"for max. connection cross section"}, {"name"=>"Rated surge voltage", "value"=>"6"}, {"name"=>"Rated voltage (II/3) power contact", "value"=>"850 V DC"}, {"name"=>"Rated voltage (III/3) power contact", "value"=>"630 V AC"}, {"name"=>"Contact diameter of signal contacts", "value"=>"1"}, {"name"=>"Litz wire cross section of signal contacts min.", "value"=>"0.06 mm²"}, {"name"=>"Litz wire cross section of signal contacts max.", "value"=>"1"}, {"name"=>"Nominal current per signal contact", "value"=>"8"}, {"name"=>"Rated surge voltage", "value"=>"1.5 kV"}, {"name"=>"Rated voltage (III/3) signal contact", "value"=>"50"}, {"name"=>"Contact diameter, data contacts", "value"=>"0.8 mm"}, {"name"=>"Litz wire cross section, data contacts, min.", "value"=>"0.08 mm²"}, {"name"=>"Litz wire cross section, data contacts, max.", "value"=>"0.5 mm²"}, {"name"=>"Rated current of each data contact at 25°C", "value"=>"3.6 A"}, {"name"=>"Rated voltage of data contact", "value"=>"50"}, {"name"=>"Material", "value"=>"1.5 kV"}, {"name"=>"Installation height", "value"=>"2000"}]}{"Housing data"=>[{"name"=>"Note", "value"=>"The suitability for assembly must be checked when fully assigned with maximum wire cross sections."}, {"name"=>"Housing material", "value"=>"Turned parts: copper zinc alloy (CuZn), die-cast parts: zinc (GD-Zn)"}, {"name"=>"Type of locking", "value"=>"for standard and SPEEDCON interlock"}, {"name"=>"Degree of protection (when plugged in)", "value"=>"IP67"}, {"name"=>"Degree of protection (when plugged in)", "value"=>"IP68"}, {"name"=>"Thread type", "value"=>"M23"}]}{"Cable seal data"=>[{"name"=>"Cable diameter", "value"=>"7.5 mm ... 9 mm"}, {"name"=>"Sealing material", "value"=>"FKM"}]}{"Environmental Product Compliance"=>[{"name"=>"REACh SVHC", "value"=>"Lead 7439-92-1"}, {"name"=>"China RoHS", "value"=>"Environmentally Friendly Use Period = 50 years"}]}