Contact insert, Contact insert, type: VC3, housing material: PA, number of positions: 51, min. conductor cross section: 0.14 mm², max. conductor cross section: 1.5 mm², Connection method: Crimp connection, Type of contact: Socket
- Contact insert
- Contact insert
- type: VC3
- housing material: PA
- number of positions: 51
- min. conductor cross section: 0.14 mm²
- max. conductor cross section: 1.5 mm²
- Connection method: Crimp connection
- Type of contact: Socket
• Positions 15, 30, 50, and 65 are available, in accordance with housing sizes VC 1 - VC 4.
• Contact types meet the requirements of IEC 60352/DIN EN 60352
• Contact carriers have two further capacitive PE contacts
• Pin and socket contacts can be used on both the plug and device sides
• The connection data of 250 V/10 A corresponds to that of the HEAVYCON DD series
Training Data Goes here
Rated voltage (III/3)
Rated surge voltage
Rated surge voltage (III/2)
Ambient temperature (operation)
-40 °C ... 125 °C
Conductor cross section
0.14 mm² ... 1.5 mm² (flexible)
Connection cross section AWG
22 ... 16
Stripping length of the individual wire
Conductor cross section flexible max.
Connectors may only be connected/disconnected when under no load.
Please note that full assembly with the maximum conductor cross-section can cause the sheathed cable to have an impermissibly large external diameter. Dimension the conductor cross-section depending on the number of positions.
Flammability rating according to UL 94
Degree of pollution
Contact carrier type
Fixed number of positions
Contact surface material
Contact carrier material
Standards and Regulations
Connection in acc. with standard
WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 4188.8.131.52 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• Observe the corresponding technical data. You will find information:o On the product On the packing label In the supplied documentation Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Operate the connector only when it is fully plugged in.
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
Environmental Product Compliance
Environmentally Friendly Use Period = 50 years