{"General"=>[{"name"=>"Note", "value"=>"Order information: Order crimp contacts 4 x Ø 1 mm, 4 x Ø 2 mm separately"}, {"name"=>"Type of locking", "value"=>"SPEEDCON locking"}, {"name"=>"Coding", "value"=>"N"}, {"name"=>"Contact connection method", "value"=>"Crimp connection"}, {"name"=>"Type of contacts", "value"=>"Socket"}, {"name"=>"Number of positions", "value"=>"8"}, {"name"=>"Contact diameter of power contacts", "value"=>"2"}, {"name"=>"Rated current for power contacts", "value"=>"30"}, {"name"=>"Contact diameter of signal contacts", "value"=>"1"}, {"name"=>"Conductor entry", "value"=>"5.5 mm ... 8.5 mm"}, {"name"=>"Pg housing screw connection", "value"=>"none"}]}{"Ambient conditions"=>[{"name"=>"Ambient temperature", "value"=>"-40 °C ... 125 °C"}, {"name"=>"Degree of protection", "value"=>"IP67"}]}{"Specifications according to DIN EN 61984:2001"=>[{"name"=>"Installation height max.", "value"=>"3000"}, {"name"=>"Nominal / operating voltage of power contacts", "value"=>"630"}, {"name"=>"Rated surge voltage of power contacts", "value"=>"6"}, {"name"=>"Overvoltage category of power contacts", "value"=>"III"}, {"name"=>"Degree of pollution of power contacts", "value"=>"3"}, {"name"=>"Nominal / operating voltage of signal contacts", "value"=>"250"}, {"name"=>"Rated surge voltage of signal contacts", "value"=>"4"}, {"name"=>"Overvoltage category of signal contacts", "value"=>"III"}, {"name"=>"Degree of pollution of signal contacts", "value"=>"3"}]}{"Standards and Regulations"=>[{"name"=>"Safety note", "value"=>"WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property."}, {"name"=>"Safety note", "value"=>"WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible."}, {"name"=>"Safety note", "value"=>"WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product."}, {"name"=>"Safety note", "value"=>"The products are suitable for applications in plant, controller, and electrical device engineering."}, {"name"=>"Safety note", "value"=>"When operating the connectors in outdoor applications, they must be separately protected against environmental influences."}, {"name"=>"Safety note", "value"=>"Assembled products may not be manipulated or improperly opened."}, {"name"=>"Safety note", "value"=>"Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products)."}, {"name"=>"Safety note", "value"=>"When using the product in direct connection with third-party manufacturers, the user is responsible."}, {"name"=>"Safety note", "value"=>"For operating voltages > 50 V AC, conductive connector housings must be grounded"}, {"name"=>"Safety note", "value"=>"Ensure that the protective or functional ground has been properly connected."}, {"name"=>"Safety note", "value"=>"VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector"}, {"name"=>"Safety note", "value"=>"Only use tools recommended by Phoenix Contact"}, {"name"=>"Safety note", "value"=>"The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product."}, {"name"=>"Safety note", "value"=>"Operate the connector only when it is fully plugged in and interlocked."}, {"name"=>"Safety note", "value"=>"Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards."}, {"name"=>"Safety note", "value"=>"Observe the minimum bending radius of the cable. Lay the cable without twisting it."}, {"name"=>"Safety note", "value"=>"The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12)."}]}{"Environmental Product Compliance"=>[{"name"=>"REACh SVHC", "value"=>"Lead 7439-92-1"}, {"name"=>"China RoHS", "value"=>"Environmentally Friendly Use Period = 50 years"}]}